PORSCHE 964 FRONT ENDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 930 1975-77 (includes uncategorized and accessory items)
10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection 91179950307 This seal sits on the trailing edge of the front fender at the top just below the windshield. Sold individually. 2 necessary per car. Driver's or passengers side fitment. View/Change Diagram
From $6.29
Make a selection KEV503032011 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon fender that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 5.9 lbs. (2.68 kg) - made of high strength kevlar and carbon. - mounting is just like factory, no modifications are necessary. Please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$1,215.50
Make a selection 115900964BI01 Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)
$3,855.50
Make a selection 96420724107 This hose connects the front of the oil tank to the thermostat housing. We recommend replacing 2 qty. Clamps, part # 99951225202 when replacing this piece. Sold individually. 1 necessary per car. Please note: this will only fit the oil thermostat with part # 964 207 047 05 or 964 207 047 07 or 964 207 047 08.
From $20.90
Make a selection 96434101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 115900991BI Only for cars without pdcc ( active stabilizer ) bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasi...(choose a part on the right to read more)
$4,153.60
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34350501 Worn bump stops and bellows can cause premature shock damage. We recommend replacing the stops and bellows with any new shock install. This set includes 2 qty. Front bump stops 96434330100 and 2 qty. Front bellows 96434350500 sold individually. 1 necessary per car.
$104.42
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 90135196411 High-quality ate, OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $14.56
Make a selection 115385 If you are looking for added damping performance on the street, the bilstein b6 performance damper is the ideal solution. The product benefits at a glance: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Marked improvement in safety and sportiness without additional spring changes. Increased service life. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested and fine-tuned by bilstein. German TUV registration is not required. Sold individually. 1 necessary per car. We recommend adding our lowering spring collars if you would like a lower ride height, our part # 115110016
$640.20
Make a selection 96434350301 This is the lower strut plate that retains the spring and sits on top of the adjusting nut. We recommend that you inspect and replace if necessary with any new shock install. This plate tends to suffer from corrosion as debris collects in it with time. Sold individually. Right or left side fitment. 2 necessary per car.
From $39.00
Make a selection BBI9964010001 Features
$525.00
Make a selection 1661900310 A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Please note: these are aftermarket calipers and do not come with the logo or brake pads. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98
$795.00
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection FVD33396410 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,726.50
Make a selection FVD33396411 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,616.41
Make a selection FS911 Das schild is a custom thermoformed, lightweight abs plastic liner designed specifically for the underside of your Porsche lid. Das schild offers Porsche owners the first and only product (patent pending) available to assist in preventing the damage that is likely to occur from overpacking the trunks without this protective liner. Das schild is the only product on the market to preserve and protect the vulnerable lids of your Porsche. Paintless dent removal (pdr) technicians have often been unsuccessful in returning the lid to its original condition. Given these unsuccessful attempts, the only alternative is to resort to costly, conventional body repair. After many years of working with these pdr technicians, t...(choose a part on the right to read more) General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1994-98 911 1989-94
$229.50
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$874.50
Make a selection BBI9964010003 Features
$550.00
Make a selection GT048A Fits under stock bumper with 9" fender flares. This is an exact replica of the factory European front spoiler. Oil cooler opening 21"x 41/2" and provision for fog lights or brake cooling ducts. General Fitment930 1975-77911 1978-83 911 1984-86 911 1987-89 911 1989-94
$570.00
Make a selection 115384 If you are looking for added damping performance on the street, the bilstein b6 performance damper is the ideal solution. The product benefits at a glance: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Marked improvement in safety and sportiness without additional spring changes. Increased service life. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested and fine-tuned by bilstein. German TUV registration is not required. Sold individually. 1 necessary per car. We recommend adding our lowering spring collars if you would like a lower ride height, our part # 115110016
$640.20
Make a selection
© 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |